Women's Business Enterprise National Council Certified Women Owned Business

2525 Industrial Blvd.
Leesburg, FL 34748

1-800-276-2833

Welcome to Technicuff - Limited-use and washable blood pressure cuffs

Single Lumen Hose Assembly

TEC-MRLD-H

The TEC-MRLD-H is a dual lumen 9 foot hose assembly that connects to monitoring systems that are utilizing a Dual Colder connector for the BP port. The TEC-MRLD-H is used with Technicuff’s UT, UA, UP and UI series of blood pressure cuff transducers. The hose assembly uses Technicuff’s “TEC-Connect" acoustical coupling device allowing facility standardization for reduction of BP cuff inventory requirements by up to 50%. The TEC-MRLD-H was originally developed for use with early Medical Research Laboratories non-invasive BP monitors. Technicuff’s eco-friendly cuff technology is economically and environmentally responsible, greatly assisting facility compliance with local, state and federal contaminated medical waste regulations.

TEC-1000-H

The TEC-1000-H is a single lumen hose assembly that connects monitoring systems that utilizing a Female Rectus connector to Technicuff’s eco-friendly BP cuff transducers. The TEC-1000-H is used with Technicuff’s UT, UA, UP and UI series of blood pressure cuff transducers. The hose assembly uses Technicuff’s TEC-Connectacoustical coupling device allowing facility standardization for reduction of BP cuff inventory requirements by up to 50%. Technicuff’s eco-friendly cuff technology is economically and environmentally responsible, greatly assisting facility compliance with local, state and federal contaminated medical waste regulations. This hose assembly is not intended for monitoring neonatal patients due to the volume of residual air in the hose assembly.

TEC-2000-H

The TEC-2000-H is a single lumen hose assembly that connects monitoring systems that are utilizing a Male Rectus connector. The TEC-2000 uses a Female Rectus to Technicuff’s TEC-connect. The TEC-2000-H is used with Technicuff’s UT, UA, UP and UI series of blood pressure cuff transducers. The hose assembly uses Technicuff’s “TEC-Connect" acoustical coupling device allowing facility standardization for reduction of BP cuff inventory requirements by up to 50%. Technicuff’s eco-friendly cuff technology is economically and environmentally responsible, greatly assisting facility compliance with local, state and federal contaminated medical waste regulations. This hose assembly is not intended for monitoring neonatal patients due to the volume of residual air in the hose assembly.

TEC-DATA-H

The TEC-DATA-H is a single lumen hose assembly that connects monitoring systems that are utilizing Male Luer connectors to Technicuff’s eco-friendly BP cuff transducers. Caution: the monitoring system uses a male lure connector that has been demonstrated to connect with indwelling fluid lines. The TEC-DATA-H is used with Technicuff’s UT, UA, UP and UI series of blood pressure cuff transducers. The hose assembly uses Technicuff’s “TEC-Connect" acoustical coupling device allowing facility standardization for reduction of BP cuff inventory requirements by up to 50%. The TEC-DATA-H was originally developed for use with early model Spacelabs Alpha series monitors. Technicuff’s eco-friendly cuff technology is economically and environmentally responsible, greatly assisting facility compliance with local, state and federal contaminated medical waste regulations. This hose assembly is not intended for monitoring neonatal patients due to the volume of residual air in the hose assembly.

TEC-HP-H

The TEC-HP-H is a single lumen hose assembly that connects monitoring systems that are utilizing Hewlett Packard's proprietary Female connector to Technicuff’s eco-friendly BP cuff transducers. The TEC-HP-H is used with Technicuff’s UT, UA, UP and UI series of blood pressure cuff transducers. The hose assembly uses Technicuff’s “TEC-Connect" acoustical coupling device allowing facility standardization for reduction of BP cuff inventory requirements by up to 50%. The TEC-HP-H was originally developed for use with Hewlett Packard monitors but is also used with Agilent and Philips non-invasive monitoring systems. Technicuff’s eco-friendly cuff technology is economically and environmentally responsible, greatly assisting facility compliance with local, state and federal contaminated medical waste regulations.

TEC-MRL1946-H

The TEC-MRL1946-H is a single lumen nine (9) foot hose assembly that connects monitoring systems that are utilizing a Female Colder PMC single port connectors. The TEC-MRL1946-H uses a Male Colder PMC single port connector to Technicuff’s TEC-connect. The TEC-MRL1946-H is used with Technicuff’s UT, UA, UP and UI series of blood pressure cuff transducers. The hose assembly uses Technicuff’s TEC-Connectacoustical coupling device allowing facility standardization for reduction of BP cuff inventory requirements by up to 50%. Technicuff’s eco-friendly cuff technology is economically and environmentally responsible, greatly assisting facility compliance with local, state and federal contaminated medical waste regulations. This hose assembly is not intended for monitoring neonatal patients due to the volume of residual air in the hose assembly.

TEC-PHY4-H

The TEC-PHY4-H is an adult single lumen monitor hose that connects to Technicuff blood pressure transducer hose assemblies. The TEC-PHY-H can be used with the UT, UA, UP or UI series of blood pressure cuff transducers. The monitor end of the hose assembly uses a single male Luer connector and the blood pressure cuff end of the hose assembly uses Technicuff's TEC-Connect. The hose assembly was originally developed for use with Physio Control defibrillators requiring a shorter 9 foot length.

TEC-PHY-H

The TEC-PHY-H is a single lumen nine (9) foot hose assembly that connects monitoring systems that are utilizing a Female Luer single port connector. The TEC-PHY-H uses a Male Luer single port connector to Technicuff’s TEC Connect. The TEC-PHY-H is used with Technicuff’s UT, UA, UP and UI series of blood pressure cuff transducers. The hose assembly uses Technicuff’s “TEC-Connect" acoustical coupling device allowing facility standardization for reduction of BP cuff inventory requirements by up to 50%. Technicuff’s eco-friendly cuff technology is economically and environmentally responsible, greatly assisting facility compliance with local, state and federal contaminated medical waste regulations. This hose assembly is not intended for monitoring neonatal patients due to the volume of residual air in the hose assembly.

TEC-PRO-CH

The TEC-PRO-CH is a single lumen coiled hose assembly that connects monitoring systems that are utilizing a Male Coulter connector to Technicuff’s eco-friendly BP cuff transducers. The TEC-PRO-CH is used with Technicuff’s UT, UA, UP and UI series of blood pressure cuff transducers. The hose assembly uses Technicuff’s TEC-Connectacoustical coupling device allowing facility standardization for reduction of BP cuff inventory requirements by up to 50%. Technicuff’s eco-friendly cuff technology is economically and environmentally responsible, greatly assisting facility compliance with local, state and federal contaminated medical waste regulations. This hose assembly is not intended for monitoring neonatal patients due to the volume of residual air in the hose assembly.

TEC-PRO-H

The TEC-PRO-H is a single lumen hose assembly that connects monitoring systems that are utilizing a Male Coulter connector to Technicuff’s eco-friendly BP cuff transducers. The TEC-PRO-CH is used with Technicuff’s UT, UA, UP and UI series of blood pressure cuff transducers. The hose assembly uses Technicuff’s TEC-Connectacoustical coupling device allowing facility standardization for reduction of BP cuff inventory requirements by up to 50%. Technicuff’s eco-friendly cuff technology is economically and environmentally responsible, greatly assisting facility compliance with local, state and federal contaminated medical waste regulations. This hose assembly is not intended for monitoring neonatal patients due to the volume of residual air in the hose assembly.

TEC-SL-H

The TEC-SL-H is a single lumen hose assembly that connects monitoring systems that utilize a Female Luer-Lock connector for the BP port. The TEC-SL-H is used with Technicuff’s UT, UA, UP and UI series of blood pressure cuff transducers. The hose assembly uses Technicuff’s “TEC-Connect" acoustical coupling device allowing facility standardization for reduction of BP cuff inventory requirements by up to 50%. Technicuff’s eco-friendly cuff technology is economically and environmentally responsible, greatly assisting facility compliance with local, state and federal contaminated medical waste regulations. This hose assembly is not intended for monitoring neonatal patients due to the volume of residual air in the hose assembly.

TEC-WEL-H

The TEC-WEL-H is a single lumen nine (9) foot hose assembly.  The TEC-WEL-H uses a non-terminated hose on the monitor end and Technicuff’s TEC-Connect on the cuff end of the hose. The TEC-WEL-H is used with Technicuff’s UT, UA, UP and UI series of blood pressure cuff transducers. The hose assembly uses Technicuff’s TEC-Connect acoustical coupling device allowing facility standardization for reduction of BP cuff inventory requirements by up to 50%. Technicuff’s eco-friendly cuff technology is economically and environmentally responsible, greatly assisting facility compliance with local, state and federal contaminated medical waste regulations. This hose assembly is not intended for monitoring neonatal patients due to the volume of residual air in the hose assembly.

Contact Us

* indicates required field.

Latest Blog Posts

What Hospitals Waste

Wednesday, February 28, 2018

ProPublica takes a look at some of the perfectly good supplies hospitals throw away.

Read more...

Study Casts New Light on Hypertension

Thursday, November 30, 2017

Using the large amount of data collected by the National Institutes of Health, the American Heart Association and American College of Cardiology have adjusted what they consider to be "high" blood pressure.

Read more...

Connect With Us